“Good appearance” is not a complete acceptance criterion for an injection molded part. Colour, gloss, texture, gate vestige, weld lines, sink, flow marks, flash, contamination and handling damage can be judged differently when the surface, lighting, distance or inspection time changes. A buyer therefore needs a written visual standard that turns product intent into a repeatable decision—not a promise that every visible variation will be eliminated.
This guide uses A/B/C surface zoning as a practical procurement framework. It does not prescribe one universal defect size or lighting value: those limits depend on the resin, colour, texture, geometry, end use and customer expectation. Use the [request-a-quote](/request-a-quote) route to give InjeForm the controlled drawing, reference samples and proposed acceptance plan for a part-specific review.
Do not approve a cosmetic part from an attractive photograph alone. Approve a defined surface map, viewing method, limit samples or defect rules, and a traceable record showing who accepted the result.
01
1. Translate product visibility into A/B/C surface zones
Start by marking the part, not by copying a supplier's generic A/B/C definition. Surface A is normally the primary customer-facing or presentation face; surface B may be visible in normal use but is less dominant; surface C is hidden, enclosed or primarily functional. The product owner should confirm the zones using the assembled product, expected orientation and user distance. A housing that looks acceptable loose on a bench may expose a gate, mismatch or flow mark after assembly.
Use a controlled CAD view, drawing overlay or labelled physical sample. Mark prohibited gate locations, logo or display windows, assembly edges, datum features and areas that can be judged only after cleaning. State whether a zone boundary follows the part geometry or the assembled product. Link the appearance map to the [DFM and tool-design](/dfm) review because gate, ejection, venting, parting line, texture and cooling decisions can affect what the buyer later sees.
| Surface zone | Typical buyer intent | Evidence to define before award |
|---|---|---|
| A | Primary visible face; appearance can influence customer perception. | Marked CAD view, approved colour/texture reference, prohibited features and strictest defect rule. |
| B | Visible during normal handling or use, but not the focal face. | Viewing orientation, acceptable feature types, size/count limits and relation to assembly. |
| C | Hidden, internal or mainly functional surface. | Functional exclusions, flash or burr rule, and any contamination or safety limit. |
| Transition or edge | Boundary where visibility changes in the assembled product. | A section or photo showing which zone governs and how edge defects are judged. |

02
2. Make lighting and viewing conditions part of the method
A visual decision is only reproducible when the observation conditions are controlled. Specify the light source or viewing booth, approximate illuminance or the applicable customer standard, background, observer position, viewing angle, distance, inspection duration and whether the part is rotated. ASTM D1729 is a useful reference for controlled visual appraisal of colour and colour differences, but it does not establish the acceptance limit for a particular molded part.[1] Colour, gloss and texture can also look different under different illuminants, so do not treat a phone photograph as the governing inspection method.
Separate colour comparison from defect search when that is the practical method. For example, a buyer may compare colour and texture against an approved master under a defined light, then inspect for flash, sink, weld lines, scratches or contamination under a specified diffuse light and angle. Record the actual setup used for approval. If a supplier proposes a different booth or light source, require equivalence to be agreed before it becomes the production method rather than silently changing the basis of acceptance.
03
3. Define defect limits without inventing universal numbers
List the defect families that matter for the part: short shot, flash, burn, splay, weld line, flow mark, sink, void, blush, gate vestige, mismatch, scratch, dent, foreign material, colour variation, gloss variation and texture damage. For each, state whether it is prohibited, conditionally acceptable or subject to a measurable limit. A defect can be acceptable on C surface yet rejectable on A surface; the same nominal size can also have a different impact on a high-gloss black face than on a textured internal wall.
Use one of three evidence types: a numerical rule, an approved limit sample, or a written visual comparator with a defined viewing method. If a numerical limit is chosen, specify how the defect is measured, including length, width, area, height or count, and whether multiple defects within a defined field are accumulated. ISO 20457 provides a framework for plastics molded-part tolerances and acceptance conditions, but it is not a substitute for the buyer's part-specific cosmetic map.[2] Avoid vague language such as ‘no visible defects’ unless the viewing conditions and the meaning of visible are documented.
Sampling also needs its own rule. Define the lot, sample size, inspection stage, cavity identification where relevant, and disposition of a failed sample. ISO 2859-1 can inform attribute-sampling plans, but the buyer should select the applicable inspection level and acceptance quality limit with quality and customer requirements in view; an AQL is not permission to ship known critical defects.[3]
| Defect or attribute | A-surface starting position | Buyer evidence to request |
|---|---|---|
| Flash, burr or sharp edge | Prohibited where it affects safety, fit or a primary visible edge; otherwise define a measurable limit. | Marked edge locations, measurement method and sample photos. |
| Gate vestige or ejector mark | Locate outside the approved focal area or define height/diameter and appearance limit. | Tool concept, gate map, limit sample and first-article photographs. |
| Sink, weld line or flow mark | Reject when it changes the agreed appearance or signals a functional risk; do not rely on size alone. | Zone-specific comparator, viewing method and engineering disposition route. |
| Colour, gloss or texture variation | Compare with the approved master using the agreed instrument or visual method. | Master sample identity, light source, instrument settings if used and retention plan. |
| Scratch, dent or contamination | Prohibit on focal surfaces unless a documented limit is approved. | Defect map, field-of-view rule, cleaning instruction and count/size limit. |

04
4. Build an approval pack that procurement can audit
The approval pack should connect the part to the decision. Retain the part number and drawing revision, resin grade and colour, mold and cavity identification, trial or production conditions, inspection date, inspector, lighting setup, surface map, photos and disposition. A signed boundary sample or golden sample can make a subjective requirement tangible, but identify its revision and storage condition; a sample that fades, scratches or is viewed under unknown light is weak evidence.
Ask the supplier to submit representative parts from the intended process, not only hand-polished or selectively photographed pieces. For a multi-cavity tool, decide whether every cavity needs appearance review and how cavity-to-cavity differences are recorded. If rework, polishing, paint, washing or protective film is allowed, state whether the acceptance decision is before or after that operation. InjeForm's [quality](/quality) information can support the discussion, while the purchase specification and approved sample should control the actual release.
Keep visual approval separate from functional, dimensional and regulatory approval. A part can pass appearance and fail fit; it can also look acceptable while lacking material traceability or required validation. For medical or safety-related products, the product owner remains responsible for the applicable regulatory and validation decision; the molding supplier supplies agreed manufacturing evidence rather than replacing that responsibility.
05
5. Use a fair escalation route for borderline findings
Define what happens when an inspector finds a borderline feature. First identify the part, zone, defect type, location, size or comparator, lighting setup and sample condition. Then route the finding to the agreed authority instead of allowing an inspector or supplier to reinterpret the standard informally. A temporary deviation should state quantity, duration, affected lots, containment and approval owner; a permanent change should update the drawing, visual standard, sample or control plan.
When comparing suppliers, send the same surface map, light method, limit samples and defect table to every bidder. Ask each supplier to return its interpretation, proposed inspection equipment, sample evidence and exclusions. This makes cosmetic capability part of a sourcing decision rather than a post-award argument. The [injection molding process](/process) and [request-a-quote](/request-a-quote) pages are useful starting points for framing the handoff, but project documents must carry the accepted limits.
Review the standard after the first controlled samples and again when resin, colour, texture, mold surface, gate, packaging or downstream assembly changes. Change control matters because a new pigment, texture or process window can alter perceived appearance even when the CAD geometry is unchanged. Record the reason for any revised limit so procurement can distinguish an approved product decision from an unplanned relaxation.

Practical takeaway
Before you move
to the next review.
- Mark A, B, C and transition surfaces on controlled CAD or a drawing using the assembled product's real visibility.
- Specify light source, background, viewing distance, angle, inspection time, rotation and colour/defect comparison method.
- List defect families by zone and define prohibited, numerical, comparator-sample or count-based limits without assuming a universal number.
- Retain revision-controlled samples, photos, cavity identity, resin/colour, inspection conditions and approval signatures.
- Set a documented borderline-finding, deviation and change-control route before production release and supplier comparison.
FAQ
Common questions
What do A, B and C surfaces mean on an injection molded part?
They are practical visibility zones: A is the primary customer-facing surface, B is visible but less dominant, and C is hidden or mainly functional. The buyer should define the zones on the actual assembled product rather than assume a universal map.
What lighting should be used for cosmetic inspection?
Use the customer or product standard when one exists; otherwise document a controlled light source or booth, background, viewing angle, distance, duration and rotation. ASTM D1729 can guide colour appraisal, but it does not set your part's defect limits.
How large can a defect be before an injection molded part is rejected?
There is no safe universal size. The limit depends on defect type, zone, colour, texture, geometry and function. Use a numerical rule, approved limit sample or written comparator with a defined viewing method, and qualify the rule with actual samples.
Can a golden sample replace a written cosmetic standard?
No. A retained sample is useful evidence, but it should be identified by revision and used with a surface map, viewing conditions, defect rules and change-control process. Samples alone can age, vary under lighting or leave borderline cases unresolved.
Should cosmetic acceptance use AQL sampling?
It may use a documented attribute-sampling plan where appropriate, but AQL does not define what a defect is or authorize known critical defects. Define defect severity, lot and sample rules with quality and customer requirements before production.
References
Source material
- [1] ASTM International, “ASTM D1729 Standard Practice for Visual Appraisal of Colors and Color Differences of Opaque Materials.”
- [2] ISO, “ISO 20457 Plastics moulded parts — Tolerances and acceptance conditions.”
- [3] ISO, “ISO 2859-1 Sampling procedures for inspection by attributes.”
- [4] ISO, “ISO 9001 — Quality management systems.”
- [5] U.S. Food and Drug Administration, “Quality Management System Regulation (QMSR).”
This guide is general information for early procurement and engineering discussion. It does not replace product-specific DFM, qualification, validation, regulatory assessment or legal advice.